![]() The only thing I haven’t tried is just disconnecting the addons for a few days to see if there is something wonky with those. ![]() I quit the sim, relaunched it a little while later, and this time none of the addons worked, but both throttles worked. I’d been using the computer all day for work.Īfter uninstalling the drivers, I opened the Sim, and it worked fine. A few hours later, I opened the sim and the problem was there. It was hit or miss if even first in the morning the control panel would work. And then calibrate from the windows Joystick panel. So if anyone is having issues with their Thrustamster sticks, try removing the Thrustmaster software, it seems pretty useless anyway. When I woke up, I launched the control panel, fidgeted with the quadrant it all worked fine. Did the calibration as instructed and then for some reason had to repeat it, but since then the spiking X-Axis problem has disappeared. Completely emptied the community folder.Removed the drivers completely (this is where I am now).Completely removed all the bits of Spad and A&O just in case.Setting the device and all the hubs to “do not shut power off” in Device Manager.Different cables (both different USB-A to USB-C cables, and a straight USB-C cable).So, here is what I have done to try and fix it: My general workaround was to reconnect the unit when I start a flight and that often lasts through the flight. When it happens, however, the same thing happens in the control panel: Engine 2 is usually the axis that works. When this happens, Windows still sees the device in device manager, and the Thrustmaster Control Panel see the unit. Sometimes, unplugging and repluging the unit in works, but the FBW REALLY hates it when that happens.Īnother frequent issue is the planes will take off and land without issue, but when I take another flight (it doesn’t really seem to matter if it’s the same craft or a different), the issue I noted above is in effect. The usual result is the flaps and spoilers don’t work, and only the engine 2 throttle working. The problem I have is around 30-40 min into the flight, most of the quadrant stops working. I have run the calibration within FBW, as well as the hardware calibration on the actual unit. I fly mainly with the FBW A320 and the 737. Neither of these I think are relevant, but hey, more data points. In order to get the flaps etc to work with the 737, I also got and Lorby’s A&O. I bought the pack around Christmas, and shortly after that also bought the PMDG 737. This seems different from the usual “loses connection” issues I’ve seen. Please note that when this has been installed the in game forcefeedback is set at 100% and you will also need to remap your buttons.įor those that think their wheel is a bit "dead" in rfactor (especially compared to rF2) you will love these settings!!įerrari F1 wheel GT Wheel The above are the official Thrustmaster profiles, as contained at ts./eng/index.I am having a frustrating, somewhat maddening problem with my Thrustmaster TCA Airbus quadrant, with the two addons. The attached downloads contain instructions as well as an "ini" file to be placed in your rfactor\userdata\controller file. Ts./download/accessories/Manuals/T500RS/T500RS_AutoCalibration_Centering_Process.pdf This means that the wheel's center value has been reset and automatically saved to the device's internal memory (you do not need to repeat the procedure every time you connect the wheel) this applies to all of the T500's wheels (GT, F1, etc.). MODE buttons on the GT wheel BO, WET & MODE buttons on the F1 wheel).ĥ) The wheel's LED briefly changes colour, then reverts to its initial colour. Position, press the START, SELECT & MODE buttons simultaneously (SE, ST & With the wheel connected to your USB and powered onġ) Turn the wheel fully to the left (until you reach the stop).Ģ) Turn the wheel fully to the right (until you reach the stop).ģ) Make sure that your racing wheel is perfectly centered while holding it in this To fix this, open your Wheel Control Panel. The second problem I had was that my wheel was not centred properly. Now, bottom right, select “Direct input” from the drop down box! To fix this issue, when you open Teamspeak, go to go “Options” “Settings” then click on the “Hotkeys” menu down the left hand side. Now this may not be unique to the Thrustmaster, but I never had this problem with my G25 or Fanatec wheel. The first problem I had was that my Push To Talk would not work properly in Teamspeak, it was very hit and miss, and when it did work it would only transmit intermittently. Since purchasing my wheel I have had a couple of minor issues that I've had to resolve so I thought I'd share them here for other that have or may have similar issues.Īlso, if anyone has any more to add, please do.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |